Blog,  Sewing & Quilting

Ironing Board Cover Sewing Tutorial

01/13/2022 /
Happy New Year friends!  I’ve made it a goal for this year to do some freshening up around my house and there is one thing that has been driving me absolutely crazy.    I’m wondering how many of you are like me… your ironing board cover is gross and so you go looking for just the right cute new cover to buy?  And there is nothing there that is even remotely appealing?   I decided it was time to make a new one and write a tutorial for all of you!   And I’m here to tell you it is so EASY.  And I mean seriously easy.   This blog post is long, with a lot of steps but don’t let that intimidate you… that is what actually makes it easy… no trying to figure out the steps without pictures!  
Fabric Selection:  before we get started gathering supplies lets talk about the fabric.  For me, this is a time when I really wanted something super fun to go with my bright and cheerful upstairs loft that is a combination sewing studio, book reading, office and movie watching corner.  My ironing board is an ever present fixture and I wanted to be happy when I look at it!  Plus ironing is a lot more fun when it’s on a pretty ironing board!  
So this is a great opportunity for you to go to a fabric store or quilt shop and just have fun browsing all the fabrics until you find what speaks to you!   NOTE:  There are plenty of online resources for purchasing fabric as well, but I love to support my local quilt shops as much as possible.   
A little more detail on fabric selection.  I wanted my ironing board cover to be more than just one fabric, so I designed it to add a couple contrasting strips at the end of the ironing board.  This is entirely your choice on whether you would like to do it this way or not.  In the Supplies list below I am listing both options in the fabric amounts.   
The final fabric I chose were four different prints from the line Sugarcube by Whistler Studios.  
Batting selection:  I used one layer of the Insul-Brite batting that is used for potholders.  It has a foil layer that provides heat protection.  It also bounces the heat back up to the fabric instead of absorbing it down to the ironing board.  You can purchase this online or at Joanns or Hobby Lobby.   You will also use a layer of regular cotton batting and I recommend the Warm and Natural cotton batting.   You can purchase both of these by the yard.  
Necessary Supplies
  • Fabric for option #1: 1-1/2 yards of fabric #1 and 1/4 yards each of fabric #2 and #3
  • Fabric for option #2:  1-3/4 yards of fabric 
  • Fabric for binding (both options):  3/8 yards of contrasting fabric
  • Quilt batting:  two pieces cut approximately 20 inches x 60 inches (one of Insul-Bright and one of Warm and Natural batting)
  • Elastic:  3 yards of 1/4 inch 
  • Scissors
  • Clover Fabric Marking Pen
  • Clover Clip ‘n Glide Bobkin
  • Clover Wonder Clips
  • Clover Rotary Cutter

Instructions

Step One:  Lets make our binding first and get that out of the way, while our ironing board is still usable!  Cut your binding fabric into four 2.5 inch strips by width of fabric (width of fabric is typically 44 inches), being sure to cut off the selvedge of each strip.  

Step Two: Sew each strip together, creating a long strip of fabric approximately 165 inches long.  

Step Three:  Iron the long strip, with seams going one direction.  Then iron in half, lengthwise.  Set this long binding strip aside for now.  (I like to roll mine up, as it holds the fold in place and keeps it from getting wrinkled until you are ready to use it.)

Step Four:   (NOTE:  Step Four and Step Five are  for Option #1, using 3 different pieces of fabric.  If you choose to use only one piece, skip to Step Six.)  Cut fabric #1 to size 20 inches wide and 42 inches long.  Cut fabric #2 to size 20 inches wide by 8 inches long.  Cut fabric #3 to size 20 inches wide by 11 inches long.  (Set aside remaining fabric for another project!)

Step Five:  Sew fabric pieces #2 and #3  together and then sew them to fabric #1.  (NOTE:  be sure they are in order when sewn together for the final strip… #1, #2, and #3.  See example on picture below.)  Press the seams to one side.  Skip to Step Seven.

Step Six:  (NOTE:  Step Six is for Option #2.)  Cut your fabric in half lengthwise so that it measures approximately 22 inches wide by 60 inches long and press well.  (Set aside remaining fabric for another project! )

Step Seven:  Now you can remove the old ironing board cover and padding from your ironing board.  Mine was super gross!

Step Eight:  Lay your prepared fabric onto the floor, right side facing down.  

Step Nine:  Turn your ironing board upside down and place on top of the fabric.   Take the time to carefully center it.  If you have chosen Option #1 with the added fabric strips be sure that the small strips are on the wide end of the ironing board.  

Step Ten:   Using a small ruler and Clover fabric marking pen, measure approximately 3 – 3.5` inches from the edge of the ironing board and make little marks all the way around.  Once you have done that, use your pen to draw a line, connecting the marks.  

Step Eleven:  Cut along the marked line all the way around.  It doesn’t have to be perfectly smooth. 

Step Twelve:  Set aside your cut fabric piece, carefully draping it so that it doesn’t wrinkle.  

Step Thirteen:  Now lay one layer of the Insult-Bright batting on the floor with your ironing board on top of it as you did in Step Nine.  Cut the batting about two inches wider than the ironing board; no need to mark it as it doesn’t have to be exact.  I just eye-balled it and it worked fine.    Repeat with the second layer of Warm and Natural quilt batting only this time cut it exactly the size of the ironing board.

Step Fourteen:  Turn your ironing board upright.  Place the smaller piece of batting on the board first with the larger piece draped over that.  Set it aside for now.

Step Fifteen:  Now lets sew the binding to the fabric cover.  Place the binding on the fabric cover, with raw edges together starting about mid-way on one long side.  I use Clover Wonder Clips to hold it in place.  Clip in place all the way around.  

Step Sixteen:  Begin sewing a few inches from one end, leaving a tail.  Sew a 1/4 inch seam allowance all the way around, removing your Wonder Clips as you go. 

Step Seventeen:  Stop a few inches away from where you started and remove the cover from the sewing machine.  Overlap the two ends 1/2 inch and cut the remaining binding off.  I marked the cut line with my fabric marking pen.  (Set aside remaining binding for another little project.)

Step Eighteen:  Open these two edges and sew them together with a 1/4 inch seam.  

Step Nineteen:  Fold the binding back in place, finger press the joint seam.  Sew it with a 1/4 inch seam to close the gap.

Step Twenty:  Once binding is sewn on, carefully clip the seam allowance around the curves on both the front and end of the ironing board cover.  Be careful not to clip through the seam. 

Step Twenty-One:  Finger press your binding down to the inside of the ironing board cover and sew an 1/8 inch top stitch all the way around.  I did not bother to pin in place, but you can if you think you need to.   

Step Twenty-Two:   After you have sewn the outside edge, you will now sew the inside edge, creating a channel to run your elastic through.  I only pinned the corners, as you’ll want to take up that slack in the binding.  Don’t worry if it doesn’t look super neat; it will be hidden!  Sew right along the inside edge of the binding fabric, stopping an inch from where you started.   In order to remind myself to stop sewing and leave that opening, I marked a line at my “stop” point with my fabric marking pen.  (Also, it doesn’t really matter where you have this opening but I chose to have mine at the wide end of the ironing board so I started and stopped my sewing there.  This opening will NOT be closed.)

Step Twenty-Three:Attach your elastic end to the Clover Clip ‘n Glide Bobkin.  (I can’t say this enough… if you do not own one, you need to get it NOW!!!  There is nothing more frustrating than a safety pin holding elastic that comes open about 3/4 of the way through.  With the Bobkin, you can rest assured your elastic is secure!  And with it being bendable, it glides through the corners perfectly!)  Thread the elastic through the channel all the way around and back out the opening.  
Step Twenty-Four:  Once you get all the way back around to where you started, you will need to do some pulling to get the elastic to feed evenly through the whole binding channel.    You don’t want the elastic to be pulled too tight and you also don’t want it super loose.  At this point you can place it over your ironing board and do some pulling and releasing to get it just right.  It’s not difficult, but it is a little time consuming to get it exactly the way you want it.  Just be patient and keep working with it.  
Step Twenty-Five:  Once you get it the tightness you want, take your two elastic ends and tie them together in a tight knot.  Then cut the ends, leaving a couple inches that you can just tuck under the cover.   I did not sew this opening closed.  For one thing it is hidden and for another you might want to tighten the elastic some more later and this makes it easy to do that.  
And there you go.  Super easy. Super cute. Super happy ironing!  
Please share your new ironing board cover by tagging me on IG @redfeedsack!  I love to see your projects using my tutorials!
Happy New Year friends!
~ Dori ~ 

You May Also Like

Tool School EXTRA CREDIT: Universal Knitting Counter

08/31/2023

Be My Valentine Baggie- Knitting Pattern

02/06/2023

Happy Spring Bunny Ear Gift Bag- Sewing Tutorial

03/28/2023